A product by Insutech Downloads EN

Announcement · April 2026

Insutech introduces Insutile® lightweight construction boards

Insutile® News

Insutile® is the lightweight construction board range made by Insutech. It was introduced in April 2026 for tiled walls and floors in bathrooms, wet rooms, kitchens and wellness areas.

A stack of Insutile® boards in different thicknesses, each with a blue XPS foam core between grey cement faces
Home/News/Insutech introduces Insutile® lightweight construction boards

The short answer: Insutile® is a range of lightweight construction boards made by Insutech and introduced in April 2026. The boards are built on a closed-cell XPS foam core. Most have a fiberglass mesh and a cement layer on both faces; Insutile® Easy Board carries a factory-bonded porcelain tile instead. The boards are used as the substrate behind tiles on walls and floors, in wet rooms and dry rooms.

This article sets out what the range contains, the figures the boards are tested to and where they are used. The datasheets and installation guides for every product are on the tools page.

What is Insutile®?

Insutile® is the construction board brand of Insutech. Insutech has worked in insulation and waterproofing for more than 35 years, operates five facilities and exports to more than 100 countries. The boards are manufactured in-house.

Insutile® Build Board, Flex Board, Angle Board, Shower Underlay and Trays and Niches are built from three layers:

  • Cement layer. A cementitious mortar coating that takes tile adhesive directly.
  • Fiberglass mesh. An alkali-resistant reinforcement under the coating.
  • XPS foam core. Closed-cell extruded polystyrene with a water absorption of 0.1 % or less.

The coating and the mesh are applied to both faces of the core. Insutile® Easy Board is different: a porcelain tile is bonded to the XPS board at the factory. The cement-faced panel is rigid, takes tile adhesive without priming, and is used in place of cement board or plasterboard as the tile substrate.

Which products are in the range?

ProductDescriptionUsed for
Build BoardFlat board in thicknesses from 4 to 80 mm. Insutile® Small is 600 × 1200 mm and Insutile® Large is 600 × 2400 mm.Walls and floors
Flex Board20 mm board with factory-cut slots that bends to a minimum radius of 200 mm.Curved walls, columns and arches
Angle Board20 mm board, factory V-scored to fold to 90°.Corners and pipe boxing
Shower UnderlayTray with the fall formed in the factory, for point or line drains. Square trays from 900 × 900 mm to 1500 × 1500 mm, rectangular up to 1000 × 1800 mm.Shower and wet-room floors
Easy BoardPorcelain tile factory-bonded to an XPS board, in panels from 30 × 30 cm to 60 × 120 cm.Roofs, walls and floors, internal and external
Trays and NichesOne-piece niches, corner shelves and seats formed from 12.5 mm board.Shower recesses, shelves and seats
AccessoriesFixing washers and screws, tapes, corner seals, waterproofing membrane, sealant and tile adhesive.Fixing, jointing and waterproofing

Sizes and thicknesses outside the standard range are customisable if needed.

What are the boards tested to?

The figures below are for Insutile® Build Board. The datasheet for each product is on the tools page.

PropertyValueStandard
Water absorption≤ 0.1 %EN 12087
Compressive strength≥ 300 kPaEN 826
Thermal conductivityλ ≤ 0.034 W/mKASTM C518
Service temperature−50 °C to +75 °CEN 13164
Reaction to fireClass EEN 13501-1

A 600 × 1200 mm board at 12.5 mm weighs about 3 kg, which is 7× lighter than cement board. The boards are manufactured under ISO 9001 and are CE marked.

Where are the boards used?

The boards are used wherever a tiled surface has to cope with moisture, heat or heavy use:

The products used in each space are set out on the solutions page.

How are the boards installed?

Boards with the Regular Coat finish are cut with a utility knife. They are fixed with screws and fixing washers, and the washers are supplied with every board. The joints are reinforced with tape before tiling. The adhesive and the fixing method are chosen to suit the substrate or structure. In showers, a waterproofing membrane is applied over the boards and joints in most cases.

The steps are in how to install Insutile® Build Board. The comparison with cement board is in XPS vs cement tile backer boards.

How can you get Insutile® boards?

Insutile® is supplied to distributors, contractors and project teams. For technical data, samples or prices, contact the Insutech team. Product videos are on the tools page.

Frequently Asked Questions

What is Insutile®?

Insutile® is a range of lightweight construction boards made by Insutech. The boards have a closed-cell XPS foam core, in most products with a fiberglass mesh and a cement layer on both faces, and are used as the substrate behind tiles on walls and floors.

Who makes Insutile®?

Insutile® is made by Insutech, a manufacturer of insulation and waterproofing systems with more than 35 years of experience, five facilities and exports to more than 100 countries.

Which thicknesses and sizes are available?

Insutile® Build Board is produced in thicknesses from 4 to 80 mm, in Insutile® Small (600 × 1200 mm) and Insutile® Large (600 × 2400 mm) panels. Other sizes and thicknesses are customisable if needed.

Are Insutile® boards waterproof?

The closed-cell XPS core has a water absorption of 0.1 % or less (EN 12087). In showers, a waterproofing membrane is applied over the boards and joints in most cases.

Specifying Insutile® for a Project?

Contact our team for technical data, samples and prices.